Page 1 of 1 1
Topic Options
Rate This Topic
#199517 - 05/06/19 07:55 PM Need S&W help.
Pa. Mike
journeyman


Registered: 07/10/09
Posts: 73
Loc: South Central Pa.

Offline
I need to replace the rear sight blade on my 5" 629 Classic with a lower sight blade. I was under the impression that when you remove the old blade you have to snap / break the retainer on the adjusting screw to get it to come off. You then need to obtain a new replacement screw when mounting the new blade. A call to S&W today resulted in a young lady telling me you only have to back the adjusting screw all the way out and she never heard of any other parts being needed. I would appreciate any input from someone who has changed this blade before. Thanks for any info provided!

Top
#199531 - 05/07/19 11:58 AM Re: Need S&W help. [Re: Pa. Mike]
Sawfish
old hand


Registered: 02/10/04
Posts: 936
Loc: Peoples Republik of Kalifornia

Offline
Years ago I had my LGS replace a sight blade and we had a discussion about the breaking sight screw. As I remember, there was a possibility that the screw might break and need to be replaced. I have replaced a few rear sight blades, but do not recall breaking a screw. These were all older Smiths. It is quite possible that the breaking screw possibility has been eliminated on the Classic models. Suggest you call Brownells Customer Service. They will have the answer and any parts you may need.
_________________________
Good Shooting Makes Good Hunting
Patron Member NRA;
Life Member RMEF, SCI, NSRPA, CRPA: Member, FTRF, HHI #7108, CBA

Top
#199533 - 05/07/19 12:39 PM Re: Need S&W help. [Re: Sawfish]
Jeff460
member


Registered: 12/01/17
Posts: 199
Loc: Kansas

Offline
I recommend changing it out to a Bowen Classic Arms all steel rear sight. I got the Target version blade for my two X-frames. They also have a Rough Country version that has opposing screws instead of click by click settings. It allows a precise locking in exactly where you want it. Check them out and you will never have a better rear sight set-up. They have models for Smith and Wesson revolvers and for Ruger revolvers.

Top
#199541 - 05/07/19 04:11 PM Re: Need S&W help. [Re: Jeff460]
Muddy
enthusiast


Registered: 01/02/07
Posts: 283
Loc: Missouri

Offline
I'm not sure the Bowen will be lower, and he may need it sooner than in a couple years.
\:\(


Every S&W sight blade I have replaced needed the adjustment screw "sheared" off first. Every one I have purchased came with the replacement. They have all come from Midway.

https://www.midwayusa.com/product/173968...ndage-nut-screw

https://www.midwayusa.com/product/987831...nd-instructions


Dan


Edited by Muddy (05/07/19 04:13 PM)

Top
#199542 - 05/07/19 04:34 PM Re: Need S&W help. [Re: Muddy]
Jeff460
member


Registered: 12/01/17
Posts: 199
Loc: Kansas

Offline
Pick your poison as back-orders from Midway can take time. But Bowen Classic Arms has them in stock and he can get a lower rear sight or get a replacement front-sight that is higher. Either way, he will get it sighted in just fine.

Top
#199547 - 05/07/19 07:50 PM Re: Need S&W help. [Re: Jeff460]
Pa. Mike
journeyman


Registered: 07/10/09
Posts: 73
Loc: South Central Pa.

Offline
Lots of good advice , thank you to all who responded.

Mike

Top
#199561 - 05/08/19 11:17 AM Re: Need S&W help. [Re: Pa. Mike]
jamesfromjersey Moderator
Shootist


Registered: 01/18/04
Posts: 9112
Loc: New Jersey

Offline
Mike, You need a "staking" tool to finish the job. I`ve changed all the sight blades on my S&W`s to white outline for my eyes. Sent you a PM...
PS- your right about snapping the screw


Edited by jamesfromjersey (05/08/19 11:17 AM)
_________________________
Life member-NRA-SCI
Member-HHI #2900-HHASA #067
Colt-Ruger-Freedom Arms-and S&W Collector Assoc.s
"I have more guns then I need but not as many as I want" "Handgun hunters HAVE to be good"

Top
#199676 - 05/16/19 08:39 PM Re: Need S&W help. [Re: jamesfromjersey]
sw282
addict


Registered: 09/01/12
Posts: 506
Loc: CSRA of GA/SC

Offline
Mike-lf your 629 Classic has removable FRONT sight blades they

can be easily switched or replaced as you see fit.. The height

is written on them... ex--.227''--.250''--.199''

They are available from S&w or Brownell. We silhouette shooters

can change the front sight out between banks of targets quicker

than trying to count clicks.. Push on your front sight with your

finger... lf it moves forward with tension you can switch them

in app 15 seconds... They aren't cheap. App $20 apiece... Last

til you lose one:-( Little springs and holder can get gone too.

Top
Page 1 of 1 1


Moderator:  Chance Weldon, jamesfromjersey, Gregg Richter, Gary 
Hop to:
 Portal Sidebar
Who's Online
0 registered and 174 anonymous users online.
Top Posters
9644
Whitworth
9608
s4s4u
9112
jamesfromjersey
7643
wapitirod
7327
TCTex.
6518
KRal
5122
Ernie
5056
Gary
4704
Tigger
4461
pab1
4370
Dan B.
4351
Franchise
4290
Chance Weldon
4119
Gregg Richter
3755
johnwilliams
  Member Hunts
Spring Hunting in
Spring Hunting in Arizona

My "Dream" Bear Hu
My

   Access Requires Login

Generated in 0.04 seconds in which 0.011 seconds were spent on a total of 14 queries. Zlib compression enabled.




Copyright © 2000-2008
HandgunHunt.com, Inc.